Elgar

Sort By:
Show
  • View as :

ELGAR 9010 PLUG-IN PROGRAMMABLE OSCILLATOR

General Description: p/n 5809010-04

PLUG IN
The 9010 Plug-In Programmable Oscillator (PIP) is a solid state  plug in controller for Elgar ATE ac sources. for the operation manual go here: http://www.programmablepower.com/products/Discontinued/Downloads/PIP9010%20Operation%20and%20Service%20604-197-90%20Rev%20June%201984.pdf  The PIP programs the frequency and amplitude of the associated power source via local control or GPIB control.

Features:

  • BCD Parallel Programming
  • Local Control and Display
  • Out of Range, Frequency Sensing and Shutdown with “soft” Restart
  • Output 0 to 2.5VAC, 45 to 5000Hz

This Elgar CW801P-108 unit is in close to new condition . It works perfectly and has been load tested. The unit is capable of producing 800VA of power in low range to 200Vrms with up to 4 amps or high range at 400 Vrms with 2.0 amps. I gaurantee this unit functionally will pass calibration by any NIST accredited laboratory. Cosmetically it is extremely good.

0-135Vac@18.6Arms or 0-270Vac@9.3Arms 45 to 500 Hz

These CW2501M units have been factory refurbished and calibrated with data 7/21/2012.

Manual CW Features And Benefits
The manual series front panel knobs (10 turn potentiometers) allow quick adjustment of voltage, current and frequency settings. Frequency and voltage can be programmed remotely using a 0 to 5V analog signal. LED’s indicate: output-on, voltage or current mode operation, fault and slave modes. Models can also be paralleled in the field or configured for three phase operation using a factory supplied cable. Current shutdown or foldback modes can be selected from a rear panel switch.

This Elgar CW801-M unit is in good condition . It works perfectly and has been load tested. I gaurantee this unit functionally will pass calibration by any NIST accredited laboratory. Cosmetically it is good.

The ContinuousWave (CW) Series of AC power sources provides clean single phase power at an impressive price/performance ratio. These compact switch mode sources come in two series, manual (CW-M) or programmable (CW-P) with standard IEEE-488.2 or RS-232 control. Both series have three power levels, 800 VA, 1250 VA and 2500 VA. The 800 and 1250 VA models are 2U (3.5″) high and allow the unit under test to be connected to the front or rear panel. The 2500 VA model is 3U (5.25″) high with rear panel output connections. All models can be operated in a benchtop or rackmount configuration.

DCS Series power supplies are 1000W and 1200W supplies designed to provide highly stable, continuously variable output voltage and current for a broad range of development, system, and burn-in applications. The DCS Series employs high frequency switching regulator technology to achieve high power density and small package size. The series consists of twelve 1000W models and twelve 1200W models. The model numbers are designated by the DCS prefix, followed by the output voltage and current ratings. For example, the model number DCS 60-18E indicates that the unit is rated at 0-60 Vdc and 0-18 Amps while a model DCS 20-50E is rated at 0-20 Vdc and 0-50 Amps. 1.2 Operating Modes The DCS Series supply has two basic operating modes: Constant Voltage and Constant Current. In constant voltage mode the output voltage is regulated at the selected value while the output current varies with the load requirements. In constant current mode the output current is regulated at the selected value while output the voltage varies with the load requirements. An automatic crossover system enables the unit to switch operating modes in response to varying load requirements. If, for example, the unit is operating in voltage mode and the load current attempts to increase above the setting of the current control, the unit will switch automatically from voltage mode to current mode. If the load current is subsequently reduced below the setting of the current control the unit will return to voltage mode automatically. 1.3 Power Supply Features • Twelve 1kW models with voltage ranges from 0-8 Vdc to 0-600 Vdc and current outputs from 1.7A to 125A. • Twelve 1.2kW models with voltage ranges from 0-8 Vdc to 0-600 Vdc and current outputs from 2A to 140A. • 115/230 Vac selectable input voltage, 50-60 Hz single phase, Installation Category II. For Indoor Use. • Simultaneous digital display of both voltage and current. M362500-01 Rev F 1-1 Features and Specifications Sorensen DCS Series 1kW and 1.2kW Supplies • Automatic mode crossover into current or voltage mode. • Ten turn potentiometer voltage and current controls permit high resolution setting of the output voltage and current from zero to the rated output. • Flexible output configuration: multiple units can be connected in parallel or series to provide increased current or voltage. • High frequency switching technology allows high power density, providing increased power output in a small, light package. • Remote sensing to compensate for losses in power leads. • Adjustable Over-Voltage Protection (OVP) • External TTL, AC or DC shutdown • Remote voltage, resistive, current limit and OVP programming with selectable programming constants. • External indicator signals for remote monitoring of OVP status, local/remote programming status, thermal shutdown, and output voltage and current. • Optional IEEE-488 interface for complete remote programming and readback capability.

This Ametek Elgar SW5250A-3-3-2 has just been factory calibrated. It is in very good condition. One of the advantages of this configuration is the first -3 in the option chain represents PFC input. This takes the unit from about 70% efficiency to about 92% efficiency, thus saving the user a lot of electricity usage and thus “money”.

This Ametek Elgar SW5250A-3-3-2 has just been factory calibrated. It is in very good condition. One of the advantages of this configuration is the first -3 in the option chain represents PFC input. This takes the unit from about 70% efficiency to about 92% efficiency, thus saving the user a lot of electricity usage and thus “money”.

SANY0781

This Sorensen DCS20-150 DC Power Supply has been fully tested. It produces up to 20Vdc output at up to 150 Amps for a total power of 3000 Watts when operated at 220 Vac 3 phase input. It can also be operated at 220 Vac input single phase for up to 2500 Watts. It is very clean, has been fully tested and in excellent condition. It comes with the input power mating input power connector kit.

These Sorensen DCS55-55 units have been tested for full functionality.They are  very nice units.   They come with a 14 day 100 % money back guarantee. They have GPIB programming capability, OVP, stand by mode. This unit requires 190-250Vac input. It can be wired for single phase which limits power output to 2500 watts or it can be wired for 3 phase which allows 3000 watts. 

X