- Description
- 0 to 300 V, 500 VA, Single Phase
- AC, DC, AC+DC output modes
- DC or 15 Hz to 1 kHz
- Delivers full power with up to 6:1 Crest Factor loads
- Analog signal input, functions as a high-power amplifier
- Programmable voltage, current limit, frequency
- Turn on, turn off phase angle control
- Powerful measurement of Vrms, Irms, Ipk, power, inrush current, frequency, crest factor, power factor, VA, and more
- Input power factor correction
- Combine 3 units for 3-phase power output
- GPIB, RS-232C, Analog Programming Interface Board
Related Products
This California Instruments 4503L-3P-4245 is in excellent condition and guaranteed to function as it was designed by the manufacturer to do. It has a low range 0-135 Vac output and high range 0-270 Vac output. It is a 5000 VA unit capable of up to 37 Amps of AC current output or 12.3 Amps per phase. The input voltage is specified at 3 phase 187 Vac to 252 Vac at from 47 to 440 Hz.
PACIFIC SMARTSOURCE 115ASX UPC1M 15-1200Hz 1500VA AC SINGLE PHASE POWER SOURCE capable of producing up to 132Vac, up to 16 amps, at 1.5KVA of power sourcing. We are offering a 90 Day warranty with full purchase price only. Not valid with BEST OFFERS or discounts of any kind. We have 3 in stock.
We have 2 of these in stock as of 8/28/2014.
The ContinuousWave (CW) Series of AC power sources provides clean single phase power at an impressive price/performance ratio. These compact switch mode sources come in two series, manual (CW 2501M) or programmable (CW 2501P) with standard IEEE-488.2 or RS-232 control. Both series have three power levels, 800 VA, 1250 VA and 2500 VA. The 800 and 1250 VA models are 2U (3.5″) high and allow the unit under test to be connected to the front or rear panel. The 2500 VA model is 3U (5.25″) high with rear panel output connections. All models can be operated in a benchtop or rackmount configuration.
ELGAR 9010 PLUG-IN PROGRAMMABLE OSCILLATOR
General Description: p/n 5809010-04
PLUG IN
The 9010 Plug-In Programmable Oscillator (PIP) is a solid state plug in controller for Elgar ATE ac sources. for the operation manual go here: http://www.programmablepower.com/products/Discontinued/Downloads/PIP9010%20Operation%20and%20Service%20604-197-90%20Rev%20June%201984.pdf The PIP programs the frequency and amplitude of the associated power source via local control or GPIB control.
Features:
- BCD Parallel Programming
- Local Control and Display
- Out of Range, Frequency Sensing and Shutdown with “soft” Restart
- Output 0 to 2.5VAC, 45 to 5000Hz
This Chroma 61601 500 VA AC source is in very good condition and was fully tested.
Output VA (Volt*Amps): 500 VA
0 to 300 V, 500 VA, Single Phase
AC, DC, AC+DC output modes
DC or 15 Hz to 1 kHz
Delivers full power with up to 6:1 Crest Factor loads
Analog signal input, functions as a high-power amplifier
Programmable voltage, current limit, frequency
Turn on, turn off phase angle control
Powerful measurement of Vrms, Irms, Ipk, power, inrush current, frequency, crest factor, power factor, VA, and more
Input power factor correction
Combine 3 units for 3-phase power output
GPIB, RS-232C, Analog Programming Interface Board and Rack Kit included
This Elgar CW801P-H unit is in close to new condition . It works perfectly and has been load tested. The unit is capable of producing 800VA of power in low range to 135Vrms and 5.9 amps or high range at 270 Vrms with 2.96 amps. The H enhancement allows a stable output at frequencies to 1000 hertz. I gaurantee this unit functionally will pass calibration by any NIST accredited laboratory. Cosmetically it is extremely good.
AC power 1,000 VA, DC power 800 W
Up to 270 Vrms output voltage
40 to 500 Hz
Measurements: voltage, current, power, AC+DC
Flexible IO: LAN/LXI Core and USB (std.), and GPIB (opt. plug-in card)
Intuitive N6700 style UI for ease of use and familiarity
This California Instruments 6000LS-3 with ADV, GPIB, HF, Mode, A350 & 704 was just repaired and factory calibrated by Ametek Programmable Power Inc., the manufacturer of the unit.
It is capable of producing 6000VA of power in 3 phase or single phase at your selection. it also has MODE option which allows switching between 3 and single pase output. in the standard configuration the output voltage ranges would be 0-135Vac (Low range) or 0-270Vac (High Range). Associated current output would be 44.4 amps or 22.2 amps in single phase output, respectively or 14.8 and 7.4 amps per phase in 3 phase mode.
This California Instruments 6000LS-3 with ADV, GPIB, HF, Mode, & 704 was just repaired and factory calibrated by Ametek Programmable Power Inc., the manufacturer of the unit. 2 in stock with these options.
It is capable of producing 6000VA of power in 3 phase or single phase at your selection. it also has MODE option which allows switching between 3 and single pase output. in the standard configuration the output voltage ranges would be 0-135Vac (Low range) or 0-270Vac (High Range). Associated current output would be 44.4 amps or 22.2 amps in single phase output, respectively or 14.8 and 7.4 amps per phase in 3 phase mode.