This Elgar CW801P-108 unit is in close to new condition . It works perfectly and has been load tested. The unit is capable of producing 800VA of power in low range to 200Vrms with up to 4 amps or high range at 400 Vrms with 2.0 amps. I gaurantee this unit functionally will pass calibration by any NIST accredited laboratory. Cosmetically it is extremely good.
This Chroma 61601 500 VA AC source is in very good condition and was fully tested.
Output VA (Volt*Amps): 500 VA
0 to 300 V, 500 VA, Single Phase
AC, DC, AC+DC output modes
DC or 15 Hz to 1 kHz
Delivers full power with up to 6:1 Crest Factor loads
Analog signal input, functions as a high-power amplifier
Programmable voltage, current limit, frequency
Turn on, turn off phase angle control
Powerful measurement of Vrms, Irms, Ipk, power, inrush current, frequency, crest factor, power factor, VA, and more
Input power factor correction
Combine 3 units for 3-phase power output
GPIB, RS-232C, Analog Programming Interface Board and Rack Kit included
This California Instruments 2001RP-OP1 is in great condition and guaranteed to pass NIST calibration. It has option OP1 so it has GPIB control.
The RP Series consists of two models, 2001RP and 2003RP. These units are ideal sources for general purpose AC power applications that require variable voltage and frequency at power levels up to 2000 VA. The 2001RP provides single phase output and the 2003RP provides three phase output. With simple knobs used to set voltage, frequency and current limit, the RP Series provides an inexpensive source of AC power in a small and lightweight package. All RP Series power source models can be used in table-top mode or rack-mounted.
This Ametek Elgar SW5250A-3-3-2 has just been factory calibrated. It is in very good condition. One of the advantages of this configuration is the first -3 in the option chain represents PFC input. This takes the unit from about 70% efficiency to about 92% efficiency, thus saving the user a lot of electricity usage and thus “money”.
This California Instruments 6000LS-3 with ADV, GPIB, HF, Mode, A350 & 704 was just repaired and factory calibrated by Ametek Programmable Power Inc., the manufacturer of the unit.
It is capable of producing 6000VA of power in 3 phase or single phase at your selection. it also has MODE option which allows switching between 3 and single pase output. in the standard configuration the output voltage ranges would be 0-135Vac (Low range) or 0-270Vac (High Range). Associated current output would be 44.4 amps or 22.2 amps in single phase output, respectively or 14.8 and 7.4 amps per phase in 3 phase mode.
This unit is in very good to excellent condition. It has been fully tested and as you can see from the various photos the unit works flawlessly. It does have one peculiarity. The front panel overlay is for that of a 5KVA unit which this is not. The unit is a 3001iX which is a 3KVA unit as identified by the part ID label on the rear of the unit. We are in the process of ordering the correct label now.
This Elgar CW801P-H unit is in close to new condition . It works perfectly and has been load tested. The unit is capable of producing 800VA of power in low range to 135Vrms and 5.9 amps or high range at 270 Vrms with 2.96 amps. The H enhancement allows a stable output at frequencies to 1000 hertz. I gaurantee this unit functionally will pass calibration by any NIST accredited laboratory. Cosmetically it is extremely good.
AC power 1,000 VA, DC power 800 W
Up to 270 Vrms output voltage
40 to 500 Hz
Measurements: voltage, current, power, AC+DC
Flexible IO: LAN/LXI Core and USB (std.), and GPIB (opt. plug-in card)
Intuitive N6700 style UI for ease of use and familiarity
The ContinuousWave (CW) Series of AC power sources provides clean single phase power at an impressive price/performance ratio. These compact switch mode sources come in two series, manual (CW 2501M) or programmable (CW 2501P) with standard IEEE-488.2 or RS-232 control. Both series have three power levels, 800 VA, 1250 VA and 2500 VA. The 800 and 1250 VA models are 2U (3.5″) high and allow the unit under test to be connected to the front or rear panel. The 2500 VA model is 3U (5.25″) high with rear panel output connections. All models can be operated in a benchtop or rackmount configuration.