Keysight AC6802A Basic AC Power Source, 1000VA, up to 270V,10A/5A 45-500Hz
AC power 1,000 VA, DC power 800 W
Up to 270 Vrms output voltage
40 to 500 Hz
Measurements: voltage, current, power, AC+DC
Flexible IO: LAN/LXI Core and USB (std.), and GPIB (opt. plug-in card)
Intuitive N6700 style UI for ease of use and familiarity
Compare
- Description
AC power 1,000 VA, DC power 800 W
Up to 270 Vrms output voltage
40 to 500 Hz
Measurements: voltage, current, power, AC+DC
Flexible IO: LAN/LXI Core and USB (std.), and GPIB (opt. plug-in card)
Intuitive N6700 style UI for ease of use and familiarity
Related Products
This Elgar CW801P-H unit is in close to new condition . It works perfectly and has been load tested. The unit is capable of producing 800VA of power in low range to 135Vrms and 5.9 amps or high range at 270 Vrms with 2.96 amps. The H enhancement allows a stable output at frequencies to 1000 hertz. I gaurantee this unit functionally will pass calibration by any NIST accredited laboratory. Cosmetically it is extremely good.
This California Instruments 2253IX AC DC Power Source Analyzer was just repaired and factory calibrated by Ametek Programmable Power Inc., the manufacturer of the unit. It is a 3 phase output unit. It produces 2250VA of output power. It can be used in low range with an output voltage of up to 150 Vac at up to 6.5 amps per phase or up to 300 Vac at up to 3.25 amps per phase of current with a maximum power rating of 2250VA or 750VA per channel in 3 phase operation. In DC mode of operation the unit can produce up to 1.63 Amps per phase at up to 400 Vdc or up to 3.25 amps per phase at up to 200 Vdc with a maximum power rating of 1500VA or 500 watts per output .
This HP 6813A has been refurbished and is in very good condition. The HP – Agilent 6813A AC Power Source / Analyzer is a single phase source / analyzer offering 45Hz to 1kHz output frequency range, 1750va output power, 300v max. rms voltage output, ±425v dc voltage range, 13a max. rms current output, 10a max. dc current output, arbitrary waveform generation, built-in harmonic analysis capability, built-in HP-IB and RS-232 interface with SCPI programming.
Key Features:
- Direct Digital Synthesis (DDS) waveform generation
- Programmable Sine, Square, or Clipped Sine waveform output
- Programmable voltage, current limit, frequency, phase, and distortion
- Power line disturbances simulation capability
- 30 factory installed harmonic waveforms in the waveform library
- User programmable harmonic waveforms
- User programmable sequential output waveforms for auto-execution
- Powerful measurement of Vrms, Irms, Ipk+, Ipk-, power, frequency, crest factor, power factor, inrush current, VA, VAR, etc.
- Built-in power factor correction circuit provides input power factor of over 0.98 to meet the IEC regulations
- Advanced PWM technology to deliver high power output in a light and compact rackmountable package
- Built-in output isolation relays
- User-definable power-on state
- TTL output to signal any output transition for ATE application
- Analog Programming Interface for external amplitude control
- Optional GPIB, RS-232 interface
- List mode transient power line disturbances simulation for Voltage Dip & Variation to meet IEC 61000-4-11
- Easy use graphic user interface: softpanel (Option)
This Elgar CW801-M unit is in good condition . It works perfectly and has been load tested. I gaurantee this unit functionally will pass calibration by any NIST accredited laboratory. Cosmetically it is good.
The ContinuousWave (CW) Series of AC power sources provides clean single phase power at an impressive price/performance ratio. These compact switch mode sources come in two series, manual (CW-M) or programmable (CW-P) with standard IEEE-488.2 or RS-232 control. Both series have three power levels, 800 VA, 1250 VA and 2500 VA. The 800 and 1250 VA models are 2U (3.5″) high and allow the unit under test to be connected to the front or rear panel. The 2500 VA model is 3U (5.25″) high with rear panel output connections. All models can be operated in a benchtop or rackmount configuration.
ELGAR 9010 PLUG-IN PROGRAMMABLE OSCILLATOR
General Description: p/n 5809010-04
PLUG IN
The 9010 Plug-In Programmable Oscillator (PIP) is a solid state plug in controller for Elgar ATE ac sources. for the operation manual go here: http://www.programmablepower.com/products/Discontinued/Downloads/PIP9010%20Operation%20and%20Service%20604-197-90%20Rev%20June%201984.pdf The PIP programs the frequency and amplitude of the associated power source via local control or GPIB control.
Features:
- BCD Parallel Programming
- Local Control and Display
- Out of Range, Frequency Sensing and Shutdown with “soft” Restart
- Output 0 to 2.5VAC, 45 to 5000Hz
This Chroma 61601 500 VA AC source is in very good condition and was fully tested.
Output VA (Volt*Amps): 500 VA
0 to 300 V, 500 VA, Single Phase
AC, DC, AC+DC output modes
DC or 15 Hz to 1 kHz
Delivers full power with up to 6:1 Crest Factor loads
Analog signal input, functions as a high-power amplifier
Programmable voltage, current limit, frequency
Turn on, turn off phase angle control
Powerful measurement of Vrms, Irms, Ipk, power, inrush current, frequency, crest factor, power factor, VA, and more
Input power factor correction
Combine 3 units for 3-phase power output
GPIB, RS-232C, Analog Programming Interface Board and Rack Kit included
This unit is completely refurbished and in excellent condition.
Output Ratings
- Power: 1750 VA
- Voltage rms: 300 V
- Current rms: 13 A
- Repetitive & non-repetitive peak current: 80 A
- Output Frequency Range DC; 45 Hz to 1 kHz
This unit is in very good to excellent condition. It has been fully tested and as you can see from the various photos the unit works flawlessly. It does have one peculiarity. The front panel overlay is for that of a 5KVA unit which this is not. The unit is a 3001iX which is a 3KVA unit as identified by the part ID label on the rear of the unit. We are in the process of ordering the correct label now.